Gaya Simulation LOWW 2.0 READY
- VDGS Support
VDGS Systems have been add to the Gates where it was possible
WIth version 2.0 I found out that sometimes the scenery VDGS is not there, therefor the placed GSX VDGS can look a bit "in the air". The scenery VDGS appears somehow sometimes again and would overlap the GSX VDGS.
Anyway, it shouldn't be a big problem, and its working :) - Custom Pushbacks add to all Stands where it is necessary
- Missing Stands which GSX does not recognize
- B47, B49, B51, B53, B57, B59, B61, B63, B67, B69, B96
- C33
- D23, D27
- F13, F35
- K42, K44, K46, K48, K50, K51
- Heavy "F" - Stands
It is possible that sometimes GSX is not recognizing the correct Parking Position.
If you load into the Sim on Stand F05/F23/F33 and do not have GSX Service, try to Select the Parking Pos again in the GSX menu that GSX is repositioning your AC correctly.
This file works only with the latest Gaya Simulations Vienna 2.0
Remote DEICE Stands (GSX Update 21.01.2023)
The profile has been updated and following remote DEICE Stands has been add:
DEICING SOUTH
- F41/F43
- F47
- F51
- F53
- F55
- F57
- F59
DEICING NORTH
- F42/F44 (I had to make 1 DEICING Stand of those 2 Stands cause it was not working if they are seprated)
- F46
- F48/F50 (I had to make 1 DEICING Stand of those 2 Stands cause it was not working if they are seprated)
How does the remote DEICE Work?
For detail information please consider the GSX manual in the GSX folder.
I'll give a "short how to do"
- Request for Pushback as usual at your Gate
- DO NOT request DEICING if GSX asked for
- After Push has been completed open the GSX menu again
- Select "Deicing Service" and the remote DEICE Stand where you want to go or which has been assigned from ATC
It looks like that the DEICE feature only works if the temperature is below 0°C.
I was only able to request DEICE if I had -1°C. I already asked in GSX forum if this could possibly be changed.
Have fun with it.
Every feedback is warmly welcome to improve the profile us much as I can :)
Cheers
3 months ago
3 months ago
AUA9085
sinter
park at C31, VDGS brings to position 1 marking but then gate doe not work.
3 months ago
3 months ago
AUA9085
ashun
4 months ago
CommanderBUS
4 months ago
Dreamliner3478
Edit: I just saw that you indeed have push-pull for C42 but not write it in the changelog.
-D21 leaves the aircraft too far back and very near the buildings for it to be safe to start engines there
-K41 straight pushback
4 months ago
arpalaiol
6 months ago
6 months ago
AUA9085
aua122
6 months ago
6 months ago
AUA9085
hennez
Hi,
gut Arbeit nur eine kleine Kritik:
In Wien haben wir dieses besondere DeIce-VDGS nicht, außerdem steht es auch da wenn die Stands nicht als DeIce Areas verwendet werden was finde ich ein sehr störender Faktor ist.
LG
1 years ago
Stimmt, ich hab die aber extra drin gelassen, damit man ungefähr weiß wie weit man nach vorne fahren muss. Leider gibts kein Marshaller der einen einweist bei den Deicing Pads :( Ich entfern sie mal, mich nerven die nämlich auch extrem :D Zur Not kann man ja FollowMe anfragen :D
1 years ago
AUA9085
clemi04
Thank you for this profile. I am from switzerland and will do a lot of flights between LOWW and LSZH. This is very much appreciated
1 years ago
hansjaegerflusi
At F5 passengers are walking below the bottom of the jetway. GSX Community says "You may open the ini and at the top, there should be jetway root floor heights defined". Seems it is missing in the ini.
1 years ago
Its a bit tricky to find the right root floor hight at Vienna. I am playing with it already but every time I change something, they Pax still below or above the Jetway on some parts... I hope I'll find a way to get that fixed.
1 years ago
AUA9085
bucmic
thank you
1 years ago
Cypher10990
Hey,
this profile works good for me, except for one point: My PAX are boarding in 20 seconds and i cant see any of them. When deboarding the PAX in Vienna, everything works as it should. I don't know where the issue is, boarding time is set to dense and works at every other airport normally.
Thanks for any help,
Regards
1 years ago
Hey,
hm... I dont think that the profile will create this behaviour.
Does it happen at every Gate in Vienna?
What are your bording time settings at all in the GSX settings?
BR
1 years ago
AUA9085
raptor27
Hi,
Love this profile. Just a little bug I think i may have found is on stand C34, it doesn't board passengers correctly. The just instantly load, perhaps an issue with the jetway positioning?
1 years ago
Hey, sorry for the late reply. Just tested it and in my Sim, they Pax are walking in the Jetway hm.
1 years ago
AUA9085
daanvb
Which is the right file?
There are 2 files in the main-download. description talk about only (put the file...)
Which file is the right one? I have read the instruction, but can find an answer
The 2 files are: T1S-42 and T2S-24
1 years ago
See Changelog:
In the zip File you will find now 2 folders:
- T1S-42: Its the bigger VDGS one which does overlap the scenery static VDGS a bit more and looks better for my taste.
- T2S-24: It's the smaller one.
1 years ago
EnterprieseE
adjan3066
Could you change the custom pushback labels from "W" to "West" and "E" to East ... happend the thrid time i hit W when i need to go in the direction of Taxiway W but it turned me to the opposite ... always forget it .... And from the F Stands most of the time i got to face towards Taxiway W for Rwy 16 ^^
1 years ago
Done ;)
1 years ago
AUA9085
EisernUnion